15mm White SPEEDFIT Collet Locking Clip - CM1815W - Pack of 10

Product Information

Speedfit Fittings have a unique grip then seal construction made up of a collet with stainless steel teeth to grip the pipe and an ‘O’ ring to provide a permanent leak proof seal. Use of the Superseal Pipe Insert ensures a double ‘O’ ring seal. Collet covers for use with standard Speedfit fittings, are available in white or in red or blue to allow colour coding of pipes. To increase the stiffness of the filament spring we are introducing Capricorn PTFE Tubing; a new, higher tolerance tube, with a tighter 1.9mm internal diameter and added internal lubricant. This has a twofold benefit - it reduces sliding friction of the filament in the tube, but most importantly it makes the filament 'spring' stiffer, by quite a lot. The tighter internal diameter permits the filament to have far less flexion than in our standard 2mm ID tubing, meaning that it can't bunch or coil up. This really firms up the response of the whole bowden system. Because the filament has no space in which to bend within the tube, movement produced by the extruder is much more efficiently translated down the tube, into the HotEnd, and out the other side. Your extruder system has a finite amount of pushing force. You want as much as possible of that pushing force to be used to generate pressure in your HotEnd, as it’s what causes the molten filament to actually extrude from the print-head (pretty crucial to 3D printing!). Of course, tools need to be used to cut pipes to size and ensure for clean connections between pipes and fittings, but to create the connection itself – no tools are required.

You just need to increase retraction and your bowden system will be as precise as a direct extruder" You just have to make sure that you don’t use poor-quality filament with an uneven diameter, which these days is far less of a concern than when we originally introduced bowden versions of E3D HotEnds. Other things you can do to improve performance include having the shortest bowden tube possible, while keeping bend radius no less than around 150mm. Bowden systems improve print quality because the resistance of the spool to unwinding no longer tugs on the print-head as it moves around" Push the pipe into the fitting, up to the pipe stop. If the Speedfit Pipe has been cut correctly the insertion mark on the pipe will be level with the collet head. The ‘O’ ring on the Superseal Pipe Insert provides a secondary seal against the bore of the fitting. A good connection has been made.An ‘O’ ring at the head of the insert and the shape of the stem, provide a secondary seal against the bore of the fitting. A combination of this and the main ‘O’ ring ensure a good connection. The stem of the insert gives greater rigidity of the length of pipe within the fitting, reducing the chance of leaks if a side load is applied. The amount of “stuff” on the print-head is much lower, and takes up less space. This can mean a smaller print head, a larger usable print volume, more extruders on one print head, or any combination of these factors. Don’t forget that bowden tubes can and do wear over time. Abrasive filament will gradually eat away at the inside of the tubing, and just the passage of filament with drive-wheel toothmarks on it will have an impact. Additionally, the ends where the couplings grip can get chewed up over time, but this is much reduced if you use our new collet clips. Those of you who've seen our new Gold V6 will have seen the swanky new Capricorn PTFE tubing and collet clips that it comes with. This blog post goes into more detail on the need for these upgrades, and how they work. TL;DR:

Initially push-fit fittings were being used for fuel systems and now they are an essential part involved with low-pressure power steering systems and aiding the development of greener engines. By diving a little deeper into the physics of where the downsides to a bowden system really come from, we can begin to understand how to improve these systems by minimising the negative effects. What needs fixing?White or grey collet clips are used with standard fittings to prevent accidental pipe disconnection. The push-fit solutions can also be found in water purification systems. These food grade fittings have been designed specifically for fluid control and drinks dispensers meaning that when using water systems in offices and other public places, water is safe to drink, while systems are easy to maintain and repair. We have a new high-performance bowden tube , and ways of making our tube couplings grip the tube more securely using a pre-tensioning clip . These will make your bowden system more responsive and reliable. Read on to find out how. What is a bowden system?

More lag/lash/hystersis/slop/whatever you want to call it. The extrusion system is simply not going to be as responsive as a direct extrusion system Ensure the pipe is free of score marks. Cut the pipe square. When using Speedfit Barrier Pipe cut along an insertion mark. We recommend the use of JG Pipe Cutters. To prevent damage to the ‘O’ ring remove all burrs and sharp edges.In the original incarnations of 3D printer extrusion systems the motor, gearing, filament drive and HotEnd were all built together in a single assembly. The extruder (motor, gearing, and filament drive) thus fed filament directly into the HotEnd.