Joined in 2023 
82 
63 About this deal
A hollow 10” to 24” metal pipe, 1” to 1-1/2” in diameter, inserted into a hole drilled vertically into the center of the ends of the two 4×4 to be butt joined, provides additional lateral reinforcement. The pipe is secured into the vertical holes with construction adhesive. Two 1/2″ through bolts are inserted into the top and bottom post pieces in holes bored through the wood and pipe. Two other reasons rest on transportation and availability issues. Carrying and connecting two 8-foot lengths is easier than transporting a 16-foot length, especially if traversing woodland trails. The availability of long 4x4s at many small suppliers is often limited due to low demand, making splicing a necessity. Repair First, it’s easier to install your sleeve plumb and level (which is essential) if you have a sturdy base for your sleeve post. It also makes it virtually impossible to pull your sleeve post out of the ground once the concrete around it is set. The simplest way to connect two 4x4s is with a butt joint. Trim the ends to be joined so they are square and smooth. Any angle, however small, can act as a shear line, and a smooth flat surface makes for a better connection.
Weatherables is known for creating pragmatic and minimalist sleeves for people on the go, and its line of weatherable 4x4 fencepost sleeves definitely falls in line with that reputation. The weatherable 4x4fence post sleeve is good for a lifetime warranty and it fits perfectly. Make sure this fits by entering your model number. Further, it is manufactured from premium - quality, durable pvc vinyl maintenance free. After fitting the pieces together, just screw them into place. 5. Place The Extender On Top Of The Post You can buy extension pieces that should fit with your original posts. Finding the right type of extender will depend on the type of fence posts in your fence. When applied to posts that meet the requirements of BS8417:2012 - UC4 (Use Class 4). See guarantee for details Wind loads and other lateral forces may need to be considered when orienting the direction of the lap. A connection with cuts perpendicular to the force is stronger than those parallel to the stress. When splicing four corner posts to support a roof structure, it may be recommended to alternate the orientation of the lap. To further strengthen half-lap joints use a construction grade adhesive like Liquid Nails or Loctite PL Premium. They are rated for interior-exterior use, waterproof, paintable, and even cure in sub-zero temperatures. We suggest fitting the joint together and clamping it in place, and then drilling the holes.
Why Manufacture Your Own Removable Fence Post?
There are several ways to remove the wood to do the lap; however, the lengths and location do play a part. A basic hand saw, hammer, and chisel, or all three have worked for centuries. Electric or battery-powered skill saws or reciprocating saws are a modern convenience that may make the task easier. I’ve seen a good hand sawer do up a set of half-laps in the same amount of time as a reciprocating saw, and with much more accuracy. There should be two bolt holes for each connected piece. Most Codes require 1-1/2” between the edge of the wood and bolt hole, which doesn’t leave much space to off-set fasteners on a 4×4. Whatever material the posts are made of, it would be smart to drill holes where you want the screws placed first. Then go ahead and put the screws in place. Doing this will prevent damaging the screw. It will also ensure that screw goes in the right direction. Make sure that the drill bit you use to create the holes is the same size as the screws you’re going to use.
Make sure that the inside diameter of your removable fence post sleeve is slightly bigger than the outside diameter of your fence post – but not too much! You want the fence post to slide in easily, but you don’t want so much room that it rattles around. Your Fence PostThe best way to join two 4x4s to extend a post is with a half-lap. The simple cuts make it ideal for a beginner or pro to make, and it’s easier to do in limited space. Adding glue, plates, and bolts increases the lateral and twist resistance to form a very strong connection. Go ahead and place the extension into position. Before you will screw it in use a level to make sure the extension is as level as you can get it. This is a really important step as not making sure the extension is in place will cause problems for your fence later. 6. Screw The Extender Into Place To remove this kind of removable fence post, you would need to remove any fence that is installed on it and then use two wrenches to loosen and remove the bolt. Easy to Manufacture from Readily Available Materials It’s very important that you don’t fill the center of your sleeve with concrete or gravel, though because this is where you will set your removable fence post when it’s in position. Coat the protruding piece of dowel with glue, or pour some glue in the holes of the upper pieces, and push it onto the dowels. Tap into place with a hammer if necessary.
Great Deal 
New Comment