Joined in 2023 
82 
63 About this deal
As shown, the same INCRA HoldDown Clamp also keeps your fingers comfortably away from the blade when cutting workpieces that are too small to safely hold by hand. The tape on the fence is movable, so it can be calibrated on the fly with fence moves and you’ll notice they thought ahead about that whole fence not touching the blade thing as they even give you some numbers on the other side of zero. The gauge can rotate 90 degrees in both directions and the positive stops are achieved via a saw-tooth design that’s incredibly effective. When the teeth are engaged, there’s zero play and you have nothing but confidence in your setting.
INCRA's Miter Express offers any miter gauge owner a safe and accurate cross-cutting and mitering platform. Shown above with an optional INCRA Miter 1000SE mounted and ready, the Express features 2 embedded T-Slot channels to secure the included Hold Down Clamp and Outboard Fence Support. These slots are also invaluable for mounting your own custom Jigs and Fixtures. ZERO side play, low-friction travel on table saws with square-sided miter slots measuring 3/4 inch (19 mm) wide, 3/8 inch (9.5 mm) deep, and with or without a 15/16 inch (23.7 mm) T-slot at the bottom. The miter bar's adjustment range accommodates actual slot widths between 0.740 and 0.765 inch (18.8 - 19.4 mm)Six expansion disks adjust both sides of the bar for ZERO side play, low-friction travel on all table saws with standard miter gauge channels, including Delta, Craftsman, imports, etc. An excellent fit in the channel directly transfers the Miter 1000HD's incredible accuracy to your project. The Miter 1000's adjustable miter bar will fit square-sided miter slots measuring 3/4" wide, 3/8" deep, and with or without a 15/16" T-slot at the bottom. The miter bar's adjustment range accommodates actual slot widths between 0.740" and 0.765". Whether it's your basic 90° cut-off, simple picture frames, or a 20-sided object, the Miter1000SE byINCRA delivers perfect, repeatable accuracy.First time, Every time, Any angle. INCRA's Miter Express offers any miter gauge owner the safest and most accurate cross-cutting platform available. Miter gauge & fence sold separately; use the Miter Express with ANY standard miter gauge! Available for traditional 3/4” x 3/8” miter slots and Shopsmith machines. Shown above with an optional INCRA Miter 1000SE mounted and ready, the Express features 2 embedded T-Slot channels to secure the included Hold Down Clamp and Outboard Fence Support. These slots are also invaluable for mounting your own custom Jigs and Fixtures. Don't let the small size fool you! The NEW Miter V120 puts high-resolution, repeatable accuracy within the budget of every woodworkers. An incredible 120 angle stops are laser cut into the steel protractor, with a stop available for every whole degree and two special stops at 22.5 degrees for cutting eight-sided frames and mouldings.
The V120's adjustable miter bar will fit square-sided miter slots 3/4" wide, 3/8" deep, and either with or without a 15/16" wide T-slot at the bottom. The miter bar's adjustment range accommodates slot widths between 0.740" to 0.760".Assembly took about 15 minutes but most of that time was spent fiddling with the darn stop. This is one of those parts you wish they included pre-assembled. The Kreg Precision Miter Gauge features an aluminum protractor head, aluminum fence, and an aluminum miter bar. That’s a bold choice for a miter bar as I can see it being a potential weak point in the design, especially at a length of 24” (the longest you’ll find on the market). The gauge can rotate 50 degrees in both directions and has a resolution of 1/10 of a degree thanks to a high visibility vernier scale. It has 9 positive stops that are engaged with a brass pin, though this is an unfortunate design choice as the pin is not fixed to the gauge and if you should happen to turn the gauge upside down, the pin falls out. I also noticed a little play at each detent, but you can overcome it by putting a good amount of pressure down on the pin and then tightening the protractor head. Flip Fences can be used with any INCRA Miter Gauge and the Flip Shop Stop. Flip Fences are NOT compatible with the standard Shop Stop. Six expansion disks adjust both sides of the bar for ZERO side play, low-friction travel on all table saws with standard miter gauge channels, including Delta, While the V27 delivers ALL the accuracy of its bigger INCRA Miter Gauge brothers, its no-nonsense design and compact size make it the most affordable INCRA Miter Gauge EVER! Now, the INCRA Miter V27 makes it possible to put an INCRA Miter Gauge in EVERY standard miter channel in your shop. The sled can be set up on either the left side or right side of the blade, and a renewable Drop Panel provides zero clearance tearout control on both sides of the blade.
The Miter V27's adjustable miter bar will fit standard square-sided miter slots measuring 3/4" wide, 3/8" deep, and with or without a 15/16" T-slot at the bottom. The miter bar's adjustment range accommodates actual slot widths between 0.740" and 0.760".
INCRA Miter Gauge Combo Pack
What makes the Incra 1000HD different is that it’s HIGH DEFINITION! If you look at the protractor head you’ll see more teeth than my new puppy Abby. That’s 180 positive stops. Yeah that’s right. A stop for every degree including 90 in both directions. And it has 1/10 of a degree resolution thanks to the vernier cursor. INCRA Miter Gauge V120 features an incredible 120 angle stops which are laser cut into the steel protractor, with a stop available for every whole degree and two special stops at 22.5 degrees for cutting eight-sided frames and mouldings. Perfect for the INCRA V27 and V120 miter gauges and upgrades the Miter 1000 to Miter the 1000SE.The Flip Fence is designed to give you outstanding fence performance and rigidity. Manufactured by INCRA from aircraft-grade aluminium extrusions, this fence profile is designed to coordinate perfectly with the INCRA Flip Shop Stop. The Incra MITER1000 SE features a 3/4" x 3/8” steel miter bar with up to six expandable nylon rings to achieve an absolutely perfect fit in any standard miter gauge slot.
Related:
Great Deal 
New Comment