Drill Hammer Chisel SDS Plus Tile Removal Tool Hammer Drill Chisel Cleaning Tools Plaster Tiles Removal Wall Shovels for Construction and Renovation

Product Information

Most of the time you should be able to fix full boards but as you get to the end you will have to make cuts. See our project here on cutting and fixing plasterboard for more help Vacuum the Area: Even after sweeping, there’s likely to be a lot of dust and small particles left behind. Use a shop vacuum or a home vacuum cleaner (with a good filter) to vacuum the area thoroughly. You may need to do this several times to fully remove all the dust. Using a drill with a mixing paddle inserted in the end, set the drill to a slow speed and mix the plaster until you get a creamy consistency that’s self supporting. If it’s too runny, slowly add more plaster powder until it’s right.

However, if you are looking to replace the skirting boards the common choices are MDF or pine skirting boards. Both come in a range of styles and sizes so you can replace like for like in most cases. How Do You Remove Skirting Boards Behind Radiators?If you have plastered up to and around any corners these will need to be defined, including any areas where the new plaster butts up to another surface. To do this you will need to use a soft, wet half-inch paint brush.

If the plaster that you want to remove is within the inside walls of your house, you will be required to remove all the pieces of furniture for the sake of avoiding further costs of repair that might be because of the breakages. You floor will also need some form of protection. You look for some old pieces of iron sheets or any other material to help you in the same for your own good. The plaster that you would have removed needs to be collected ad taken to a different place hence there will be the need to have the garbage can with you so that the process becomes simple and effective. In case the wall of your house has, some screws or certain plates do not just work on it that since you might them later. Using a screwdriver, you can safely remove them and have them kept at a secure place for future use. Before you apply any finishing coverings, fill and sand any holes or depressions so that you get a perfect flat finish. Use a half-inch, wet (water), soft paint brush to define corners and the abutment of the plastered surface to any other. Before using a wallpaper steamer it needs to be prepared and this means filling it with clean water up to the max fill line on the tank and then screwing the lid on fully.

Does Artex Contain Asbestos?

With this in mind, you can use a plasterboard lifter to lift and hold the boards in place or you can enlist the help of a family member or friend to hold the boards up while you fix them. Plastering is very hard work indeed. Mostly because of the speed it has to be carried out at & also because it involves a lot of body movement. Please make sure you have divided the room onto manageable areas. You really do only want to do this once As we have stated above, plasterboard is bulky and heavy and can be a nightmare to position and hold in place as you fix it, especially if you’re working on a ceiling. Plaster Boarding Again a very effective way of resolving an artex problem, especially if it contains asbestos. Like the plastering route, it simply involves boarding over the artex using plasterboard. If you do it yourself and don’t plaster it, it can be fairly cheap, however if you use tradesmen and have it plastered, again it can be rather expensive

Skim plaster is bought in bags of 25kg (Smaller bags can be bought for patching) and the mixing instructions are on the bag. Each tool would be used in a separate place, and this technique is usually good right at the start to get the board moving. Removing skirting boards fixed with screws Stripping artex with a steamer cannot be done at speed, you will need to work slowly and methodically as if the steam plate is left in one area too long, there is a possibility of damaging the ceiling or wall behind it as the steam will penetrate through and soften this also, which you certainly don’t want.

Protect Floors

Remove Using Eco Solution X-Tex: X-Tex is one of the only products available that can be used to remove atrex with asbestos in it. As it’s gel-based, all the fibres are held within the gel, preventing them from getting into the air In some cases Skirting boards will be screwed. In this case you need to determine what type of wall it is fixed too, as this will affect the way you remove the boards. Sweep Up Smaller Pieces: After you’ve removed the larger pieces, sweep up the smaller pieces of debris. A stiff-bristle broom is particularly effective for this. Be careful to collect any nails or other sharp objects.

If you’re not sure about something or if it’s a larger project, it might be best to hire a professional. They can safely remove the plaster and handle any unexpected issues that might arise. Related Plastering Articles If the skirting boards are on a stud wall and they have been screwed, this is probably the most challenging. The reason for this, is you can’t simply lever them off the wall. Instead you will need to unscrew them.

Don’t Mix Plaster and Lath

Use Different Tools: If increasing the force isn’t working or isn’t an option, you could try using different tools. A pry bar might be useful to get underneath the plaster and apply pressure in a different way. The purpose of scoring the plaster is to create control lines or breaks in the plaster, which will help when you begin to chisel it off. By scoring the plaster into squares, it will break along these lines, reducing the risk of large, unmanageable pieces falling at once and making the process safer and cleaner. Choosing a Utility Knife For really stubborn nails use an angle grinder or multi-tool to cut the nail tight against the skirting.