4'' Smooth Wheel Replacement for Hoverkart, LS&GHY Hoverboard Go Kart Front Rubber Wheel Replacement

Product Information

We offer a 12-month manufacturer’s warranty. This warranty covers any mechanical or electrical faults that may arise during normal usage. Please note that the warranty does not cover damages caused by misuse, water exposure, or modifications. Please refer to hoverboard warranty terms and conditions. Smooth Ride: The replacement wheel's smooth tread pattern and precision bearings offer a comfortable and enjoyable riding experience on various terrains. Prior to riding your hoverboard ( on its own or with the kart attached), make sure the internal balance mechanisms are in line. You can do this by recalibrating your hoverboard—basically giving those balance mechanisms a reset.

Your hoverboard will give you signs—spinning or beeping, for example—whenever it needs another recalibration.

Support

The responsibility of manufacturer shall be limited to the repair or replacement of the product at its sole discretion. Grab the 2 footrests and 3 smallest screws from your hardware supply. Set 1 screw with your other space pieces; you will only need 2 here.

Easy Control with More Fun: Easily Shifting accelerating, turning, and brake smoothly via 2 hand control bars. The 360° flexible PU front wheel let you turn around freely Save 1 washer and 1 bolt in a safe place in case you ever need them; those are spares. Slip 1 washer onto each of the 4 remaining bolts. Align the 3 pre-drilled holes at the front of the kart with the 3 holes in the inside of the nose cap.With the hoverboard charged, calibrated, and powered off, level both sides of the hoverboard so that they are evenly aligned and parallel with the ground. If necessary, free the loose ends of the Velcro straps and the wire on the underside of the seat kart so that they are accessible. Troubleshooting: If after inserting the screw into your footrest, you cannot toggle the footrest at all, you have likely inserted the screw without the two holes properly aligned. Remove the screw, realign the holes, and re-insert the screw. From your collection of hardware, look for the 5 washers and 5 large metal bolts. (Not the largest plastic ones; you’ll use those later.) Please note that this is not a guaranteed next day delivery service, and we do not take responsibility for any delays.)

Remarks: Hover-1 reserves the right, at its sole discretion, to interpret, modify and amend this warranty policy at any time. The manufacturer will not take any responsibility if the failure of the unit has resulted from accident, abuse, misuse, or any unauthorized repair, modification or disassembly.For safety reasons and because certain repairs can be complicated, we do not offer replacement parts for internal components or fully integrated batteries. (If something has gone wrong with the inner workings of your Jetson, do not try to open it up! Instead, reach out to us for troubleshooting and product support.) Goods outside 30 calendar days shall be issued with a replacement or repair only depending on the warranty length of the product. Slide one footrest onto each bar. Rotate the footrests so that the screw hole on each footrest aligns with the oblong hole on each side of the kart. This warranty gives you specific legal rights, and you may also have other rights which vary under local laws. The following conditions comprise the requirements and scope of our warranty conditions and do not affect our legal and contractual warranty obligations. Where a product develops a fault, a repair or replacement will be offered, as long as the item is within its manufacture warranty timescale.

Locate the 2 holes on each footrest: a large hole on the end that will slip onto the kart frame, and a small hole for the screw that is inside the curve on one side. Remove the charger from the hoverboard’s charging port and wall outlet. Replace the cover on the hoverboard charging port. Compatibility & Flexibility: This universal hoverboard seat attachments can fit most 6.5'' 8'' 8.5'' 10'' hoverboards. Length can be adjusted between 31- 44 inches. Suitable for riders between 100cm – 200cm. max load is 100 Kg

Remix ownership 

Simple Assemble: Turn your Hoverboard into Hoverboard Kart within 10 minutes with only 5 assembly steps. Detailed instructions are provided in the manual, feel free to reach out to our customer service team for any questions Items not including hoverboards, hoverkarts, and electric scooters will be shipped using the EVRI delivery service. Comfortable Seat with Stable Frame: Ergonomic seats and aerospace-grade material frames can ensure your comfort and safety while you enjoy the ride. Enhanced straps are equipped to ensure safety of the attachment. Extra 2 enhanced straps are provided in case of any wear and tear When seated on the kart with both feet positioned on the footrests, riders should have a slight bend in the knees. Shorten or lengthen the kart, if necessary, to accommodate the size of the rider.