Posted 20 hours ago

Everbuild Filler Coat Thick Base Coat, White, 5 Litre

ZTS2023's avatar
Shared by
Joined in 2023

About this deal

If you are using a powdered filler, mix this according to the product instructions to a paste, ready to apply to the wall. Step 4 Whether that be brush or roller, either will work. I would recommend using a roller and cutting in at the edges with a brush. Using the wrong type of roller can cause foaming of a paint film. Sponge or foam rollers should be avoided with water-based paints. Long pile rollers must be wetted out properly. Foaming happens when air gets into the wet paint film to create air bubbles. When these bubbles burst craters are left on the film surface. Sometimes these craters dry to give an even film. Putting it right Make sure that all filled areas are rubbed down smooth and level. You will need to prime the filler before painting to prevent subsequent coats being absorbed more rapidly than on other areas. Use a coat of Dulux emulsion thinned 10-20% with clean water. Once this is dried you can apply a full coat of Dulux emulsion.

Newly plastered walls and surfaces are porous, so using a primer before applying subsequent layers of undercoat and paint is key to a great finish. Primer paint is the first layer of paint you will apply to your surface. If you are painting wood or metal, you will have already prepared your surface by sanding and descaling etc. Primer paint should be the first stage of your coating and paint system. If you’re painting over a dark colour with a lighter colour, priming the wall will help to cover the dark wall, and your new colour look more saturated and pigmented, without the need for lots and lots of layers. When painting over a dark coloured wall with primer paint, take as much care as you would with your new colour. If the primer looks patchy and uneven, your new colour will too.However, using a primer is almost always worth the extra effort. The primer adds a layer between your raw surface and subsequent coats of paint. On porous surfaces, this smooths out the surface, avoiding the need for unnecessary coats of paint later and an uneven final result. Etch primer is used on untreated ferrous metals including aluminium, zinc, copper, brass, tin, and steel. Apply with a brush, or spray. Comprehensive Research: Our team dedicates extensive time and effort to research and analyze products, so you can make informed decisions.

Softwood can be especially prone to resin exudation, where the natural resin comes to the surface, staining the wood. This resin makes it difficult for paint to adhere to the wood. Apply an aluminium primer to your wood if this happens. The primer will stop the resin from seeping through and compromising your paint system. The filler will need to be spread over the Artex with a wide jointing/smoothing knife or equivalent. The kit below provides all the tools you will need to apply and smooth off the filler. If you’re painting over a glossy surface, it’s hard for the paint to adhere without the use of primer. If your walls have previously been covered with high-gloss or enamel paint, you will almost certainly need to apply a primer paint before you start painting and may even need to gently sand the surface before priming if it is very high-gloss.On most metal surfaces, one coat of primer is enough. Because metal is not a porous surface like plaster and wood, the primer doesn’t have to absorb into the metal. Its job is to ensure that subsequent layers of paint adhere to the surface and one coat will be enough to do this. How Many Coats of Primer On Plaster? This can be done with regular old emulsion, but if you want to try and get the best results on a budget, then you could opt for something like a Filler Coat Paint.

This dead wood must be completely removed by rubbing it down to new sound wood. If outside, the wood can then be primed with Weathershield Exterior Preservative Primer followed by the Weathershield Undercoat& Gloss. Rotten wood Cause In most cases, you should prime your surface before you start painting. For wood or metal painting projects, it is essential to prime your surface. Because wood is porous, a layer of primer paint stops your paint from soaking into the wood. Primer also helps your subsequent coats of paint to adhere to your surface – especially important for metal or glossy surfaces.


If you want colour make sure to prime and undercoat properly and use the best exterior wood paint to give a good finish. Expect to repaint every three to five years. What is the Best Way To Paint Plywood Edges?

Universal wood/metal primers can be used on new wood, masonry, metal, and plaster, inside and outside. Apply with a brush and clean with white spirit afterwards. Primers for Plaster It’s imperative to use a primer on bare plaster. This image shows what happens if you paint straight onto bare plaster without priming with a mist coat first. MDF Unpainted MDF needs sealing before painting. Use a specialist sealant such as Johnstone's MDF primer followed by an undercoat, before glossing or eggshelling. When the surface is thoroughly dry the affected surface will need to be rubbed down using 'wet and dry' abrasive paper. It can then be re-coated. This should only be done once the conditions improve or when the condensation problem is resolved. Industry Connections: We maintain close ties with manufacturers and brands, offering insights into trends and upcoming products.Spirit-based primer can be used on indoor and outdoor surfaces. The shellac-based primer is great for sealing over stains and odour on interior walls and ceilings, and can be used for spot-priming exterior surfaces. Apply with a brush, roller, or spray. Metal Specific Primers Whether you’re covering a dark colour on interior walls, painting wooden doors, or adding paint to your metal surfaces, it can be tempting to get your new colour on straight away. Start by filling any dents, imperfections, knot holes and nail and screw holes with a decent wood filler such as Everbuild Multi-Purpose Wood Filler. If the edges are going to be seen, paint the edges, fill and rub down. Application: Apply a generous coat by airless spray followed immediately by tipping off with a medium pile roller. For airless spray application, we recommend a minimum working pressure of 140 kg/cm² (2000 Ib/sq in) with a spray tip size of 19 thou and a fan of 12 inches. May also be applied by brush, roller or conventional spray. When applying by spray, work into all pores and voids with the first pass, then finish with a full coat. If applying by brush, remove brush marks with a partially loaded roller while the filler is still wet. Do not apply if the surface temperature is below 10°C. Aluminium wood primer is used on softwoods and on surfaces that have been previously treated with wood preservative. Apply with a brush and clean your equipment with white spirit.

Asda Great Deal

Free UK shipping. 15 day free returns.
Community Updates
*So you can easily identify outgoing links on our site, we've marked them with an "*" symbol. Links on our site are monetised, but this never affects which deals get posted. Find more info in our FAQs and About Us page.
New Comment